欢迎访问《轻工机械》稿件在线采编系统!设为首页 | 加入收藏    
信息公告: . 2013年《轻工机械》再次被收录为“中国...  
文章检索:
稿件处理系统
期刊信息
  • 中国标准连:ISSN1005-2895
  • 续出版物号: CN 33-1180/TH
  • 主管单位:轻工业杭州机电设计研究院有限公司
  • 主办单位:轻工业杭州机电设计研究院有限公司、中国轻工机械协会、中国轻工业机械总公司
  • 社  长:刘安江
  • 主  编:黄丽珍
  • 地  址:杭州市余杭区高教路970号西溪联合科技广场4-711
  • 电子邮件:qgjxzz@126.com
理事单位          MORE>>
程海, 袁跃峰, 谢飞, 李德然.螺杆传动式贻贝卸苗设备设计[J].轻工机械,2021,39(2):23-28
螺杆传动式贻贝卸苗设备设计
Design of Screw Driving Mussel Breeding Rope Removal Equipment
  
DOI:10.3969/j.issn.1005 2895.2021.02.005
中文关键词:  贻贝卸苗  卸苗机械  螺杆传动  有限元分析  PLC
英文关键词:mussel breeding rope removal  seedling removal machinery  screw drive  FEA(Finite Element Analysis)  PLC(Programmable Logic Controller)
基金项目:舟山市科技计划专项:贻贝专用采收船的研制(2014C41014);横向项目:嵊泗县贻贝产业链提升发展若干技术研究。
作者单位
程海, 袁跃峰, 谢飞, 李德然 浙江海洋大学 海洋工程装备学院 浙江 舟山316022 
摘要点击次数: 256
全文下载次数: 182
中文摘要:
      针对目前贻贝卸苗工序存在自动化程度低、操作繁琐及工人配置不合理等问题,课题组提出了一种螺杆传动式贻贝卸苗设备。借助目前所使用的卸苗设备,课题组从工作环境进行分析,确定卸苗需要的拉力,作为新型设备的设计依据;采用了SolidWorks软件和Simulation模块分别对设备进行结构建模和关键部件的有限元仿真,同时对设备控制系统进行了设计。仿真结果表明:该设备的部件之间装配合理且无干涉存在;卸苗钩和卸苗模具最大应力分别为33.9 MPa和5.89 MPa,均未超出屈服极限206 MPa,最大变形量分别为1.800 mm和0.049 mm,均不影响卸苗作业要求;机架前5阶共振频率段为13~19 Hz,未与卸苗作业振动频率发生重合。设计的贻贝卸苗设备安全可靠,可长时间运行。
英文摘要:
      Aiming at the problems of low automation, cumbersome operation and unreasonable configuration of workers in the current mussel breeding rope removal process, a screw drive type mussel breeding rope removal equipment was designed.With the aid of the breeding rope removal equipment currently used, the work environment was analyzed to determine the pulling force required for breeding rope removal, as the basis for the design of new equipment.SolidWorks software and Simulation module were used to carry out structural modeling and finite element simulation of key components of the equipment, respectively, and the equipment control system was designed.The simulation results show that the components of the equipment are reasonably assembled and with no interference; the maximum stress of the breeding rope removal hook and the mold are 33.9 MPa and 5.89 MPa respectively, neither of which exceeded the yield limit of 206 MPa, and the maximum deformation is 1.800 mm and 0.049 mm, which does not affect the requirements for operation of breeding rope removal; the first 5th order resonance frequency section of the frame is 13 19 Hz, which does not coincide with the vibration frequency of breeding rope removal process. The designed mussel breeding rope removal equipment is safe, reliable and can run for a long time.
查看全文  查看/发表评论  下载PDF阅读器
关闭