欢迎访问《轻工机械》稿件在线采编系统!设为首页 | 加入收藏    
信息公告:  
文章检索:
稿件处理系统
期刊信息
  • 中国标准连:ISSN1005-2895
  • 续出版物号: CN 33-1180/TH
  • 主管单位:轻工业杭州机电设计研究院有限公司
  • 主办单位:轻工业杭州机电设计研究院有限公司、中国轻工机械协会、中国轻工业机械总公司
  • 社  长:刘安江
  • 主  编:黄丽珍
  • 地  址:杭州市余杭区高教路970号西溪联合科技广场4-711
  • 电子邮件:qgjxzz@126.com
理事单位          MORE>>
高浩1,3, 宁振忠2,3, 韦存超2,3, 赵思思1,3.带V形肋片太阳能空气集热器的空气流动及换热特性模拟研究[J].轻工机械,2025,43(1):37-46
带V形肋片太阳能空气集热器的空气流动及换热特性模拟研究
Simulation Study on Air Flow and Heat Transfer Characteristics of Solar Air Collectors with V Shaped Ribs
  
DOI:10.3969/j.issn.1005 2895.2025.01.006
中文关键词:  太阳能空气集热器  V形肋片  强化换热  通道宽度  节距  
英文关键词:solar air heater  V shaped rib  heat transfer enhancement  channel width  pitch  ANSYS FLUENT
基金项目:
作者单位
高浩1,3, 宁振忠2,3, 韦存超2,3, 赵思思1,3 1.青岛海尔空调电子有限公司 山东 青岛226000 2.青岛海尔空调器有限总公司 山东 青岛226000 3.数字家庭网络国家工程研究中心 山东 青岛226000 
摘要点击次数: 10
全文下载次数: 6
中文摘要:
      为探究空气在带有V形肋片的太阳能空气集热器中的传热和流动特性,笔者基于ANSYS FLUENT软件进行了数值模拟,重点研究了肋片几何参数对通道内空气流动及换热特性的影响。仿真结果表明:通道宽度方向V形肋片数的变化会对传热性能产生正反2个方面的影响,在肋片几何参数及节距不发生变化的条件下可以得到最大的热性能因子对应的肋片数(宽度方向),当肋片几何参数发生变化时最大的热性能因子对应的肋片数(宽度方向)也发生变化,在所研究的肋片参数范围内热性能因子最大为2.30;只增大肋片迎角或节距时最大热性能因子对应的肋片数(宽度方向)将减少,只增加肋高时最大热性能因子对应的肋片数(宽度方向)先增大后减少。
英文摘要:
      To investigate the heat transfer and flow characteristics of air in a solar air collector with V shaped ribs, the author conducted numerical simulation research based on ANSYS FLUENT software, focusing on the influence of fin geometry parameters on air flow and heat transfer in the channel. The simulation results show that the change in the number of V shaped ribs in the width direction of the channel will have two positive and negative effects on the heat transfer performance. Under the condition that the geometric parameters and pitch of the ribs do not change, the maximum number of ribs corresponding to the thermal performance factor (width direction) can be obtained. When the geometric parameters of the ribs change, the number of ribs corresponding to the maximum thermal performance factor (width direction) also changes. Within the range of rib parameters studied, the maximum thermal performance factor is 2.30; When only increasing the angle of attack or pitch of the ribs, the number of ribs (in the width direction) corresponding to the maximum thermal performance factor will decrease. When only increasing the rib height, the number of ribs (in the width direction) corresponding to the maximum thermal performance factor will first increase and then decrease.
查看全文  查看/发表评论  下载PDF阅读器
关闭